Infrared anti-theft fence installation instructions:
Determine the installation position so that the installed defense beam can effectively block the target channel, and mark the mounting holes of the four mounting seats on the mounting surface to ensure that the emission receivers are aligned and parallel to each other;
Use a sharp object such as a screwdriver to break the threading hole of the lower end of the infrared anti-theft fence, break the power cord through the threading hole of the mounting seat, and then pass through the threading hole of the wire holder. Finally, the positive and negative levels of the power cord are according to the power cord. "+", "-" mark correct access terminal and tighten;
Use a φ6 bit to drill the mounting holes in the mounting surface, nail into the plastic column, and then use M4 tapping screws to fix the upper and lower mounting blocks;
Confirm that the transmitting end and the receiving end correspond to each other: When the wiring is powered on, the power indicator of the transmitting end indicates that the green light is on, and the working indicator indicates that the red light is intermittently flashing; when the two are aligned with each other, the alignment of the receiving end indicates that the red light is off and the buzzer does not sound When using an opaque object to block any two adjacent beams at the same time, the alignment of the receiving end indicates that the red light intermittently flashes, the buzzer intermittently sounds, and a wired/wireless alarm signal is issued; Note: Adjustment When selecting the angle, try to debug when the working environment with the strongest sunshine or fog is the most unfavorable.
Fasten the fastening screws on the transmitter and receiver mounting bases, and then install the upper and lower mounting cover to complete the installation.
When one of the following conditions occurs, the receiver will issue a wired/wireless alarm signal:
An object simultaneously blocks any two adjacent infrared beams;
Disconnect the power from the transmitter or receiver (cut the power cord manually);
Move the position or direction of the transmitter or receiver.
Receiving terminal wiring instructions:
SW: Both ends of the tamper switch are normally closed when the lead frame is normally installed, and both ends are "normally open" when the lead frame is pulled out;
+: DC12V power supply positive
-: DC12V negative power supply;
TO: refer to the transmit terminal TO;
COM: relay output common;
NC: Relay output normally closed (in normal operation);
NO: Relay output normally open (in normal operation).
Jump pin instructions:
Buzzer jumper: "BEAP" is shorted to "ON" (open) and the buzzer is sounded, shorted to "OFF" (off) as the buzzer does not sound;
Wireless control jumper: "REMOT" is shorted to "ON" (open) for normal use, short to "TEST" (test) for test state, control wireless normally open or normally closed;
Wireless test jumper: "TEST" is shorted to "ON" (open) for normally open use, short to "OFF" (off) for normally closed state;
Coded jumper: used for high frequency encoding, area A is data code, others are address code (L is low, H is high).
Transmitter terminal wiring instructions:
SW: Both ends of the tamper switch are normally closed when the lead frame is normally installed, and both ends are "normally open" when the lead frame is pulled out;
Emission distance terminal: Shorted to "LOW" (close) for short-distance, short-circuited to "MID" (medium) for middle distance, short-circuited to "FAR" (far) for long distance;
+: DC12V power supply positive
-: DC12V negative power supply;
TO: Connect the transmit end and the receive end TO to the wire, and connect the transmit end to the negative end of the receive end to enter the strict defense mode (this mode has strong anti-high intelligence malicious destruction capability). When it is not connected, it enters the general defense mode (this mode has a strong anti-interference ability, the wiring is also relatively simple). When the connection wire is artificially disconnected or connected, an alarm signal will be issued immediately.
Determine the installation position so that the installed defense beam can effectively block the target channel, and mark the mounting holes of the four mounting seats on the mounting surface to ensure that the emission receivers are aligned and parallel to each other;
Use a sharp object such as a screwdriver to break the threading hole of the lower end of the infrared anti-theft fence, break the power cord through the threading hole of the mounting seat, and then pass through the threading hole of the wire holder. Finally, the positive and negative levels of the power cord are according to the power cord. "+", "-" mark correct access terminal and tighten;
Use a φ6 bit to drill the mounting holes in the mounting surface, nail into the plastic column, and then use M4 tapping screws to fix the upper and lower mounting blocks;
Confirm that the transmitting end and the receiving end correspond to each other: When the wiring is powered on, the power indicator of the transmitting end indicates that the green light is on, and the working indicator indicates that the red light is intermittently flashing; when the two are aligned with each other, the alignment of the receiving end indicates that the red light is off and the buzzer does not sound When using an opaque object to block any two adjacent beams at the same time, the alignment of the receiving end indicates that the red light intermittently flashes, the buzzer intermittently sounds, and a wired/wireless alarm signal is issued; Note: Adjustment When selecting the angle, try to debug when the working environment with the strongest sunshine or fog is the most unfavorable.
Fasten the fastening screws on the transmitter and receiver mounting bases, and then install the upper and lower mounting cover to complete the installation.
When one of the following conditions occurs, the receiver will issue a wired/wireless alarm signal:
An object simultaneously blocks any two adjacent infrared beams;
Disconnect the power from the transmitter or receiver (cut the power cord manually);
Move the position or direction of the transmitter or receiver.
Receiving terminal wiring instructions:
SW: Both ends of the tamper switch are normally closed when the lead frame is normally installed, and both ends are "normally open" when the lead frame is pulled out;
+: DC12V power supply positive
-: DC12V negative power supply;
TO: refer to the transmit terminal TO;
COM: relay output common;
NC: Relay output normally closed (in normal operation);
NO: Relay output normally open (in normal operation).
Jump pin instructions:
Buzzer jumper: "BEAP" is shorted to "ON" (open) and the buzzer is sounded, shorted to "OFF" (off) as the buzzer does not sound;
Wireless control jumper: "REMOT" is shorted to "ON" (open) for normal use, short to "TEST" (test) for test state, control wireless normally open or normally closed;
Wireless test jumper: "TEST" is shorted to "ON" (open) for normally open use, short to "OFF" (off) for normally closed state;
Coded jumper: used for high frequency encoding, area A is data code, others are address code (L is low, H is high).
Transmitter terminal wiring instructions:
SW: Both ends of the tamper switch are normally closed when the lead frame is normally installed, and both ends are "normally open" when the lead frame is pulled out;
Emission distance terminal: Shorted to "LOW" (close) for short-distance, short-circuited to "MID" (medium) for middle distance, short-circuited to "FAR" (far) for long distance;
+: DC12V power supply positive
-: DC12V negative power supply;
TO: Connect the transmit end and the receive end TO to the wire, and connect the transmit end to the negative end of the receive end to enter the strict defense mode (this mode has strong anti-high intelligence malicious destruction capability). When it is not connected, it enters the general defense mode (this mode has a strong anti-interference ability, the wiring is also relatively simple). When the connection wire is artificially disconnected or connected, an alarm signal will be issued immediately.