Before installation of squat toilets, squat traps are often installed. Many owners do not know much about the installation steps and dimensions of squat toilet traps. In fact, the installation of squat toilet traps directly affects us. After daily life. Let's take a look at the installation steps and dimensions of the siphon traps for your reference.
Three installation options for squat traps on the second floor and above:
1, surface mounted, traps installed under the ceiling under the floor;
2, buried in the floor above, fill in the dregs, do cement cushion, raise the floor leveling;
3. At the location of the raft, the floor will be settled (castern) and the trap will be buried with the residue soil.
The traps form a "water seal", mainly to prevent the odor of the septic tank from overtaking. If there is no trap, then the effect must be something you do not want to know!
Squat pan trap installation steps
1. If a drain plug is installed at the bottom of the bent portion of the trap, use a wrench to remove the drain plug and drain the water inside the trap to the bucket. If there is no drain plug, you should loosen the slide nuts and move them out of the way.
2. If the trap is a rotary type, the bent part of the trap can be freely removed. However, keep the trap upright when disassembling, and drain the water after removing the part. If the trap is stationary and does not rotate, unscrew the tailpipe slide nut at the drain flange and the slide nut at the top of the trap. Push the tail pipe down into the trap, and then turn the water trap clockwise until it can drain the trap water. Pull out the tail pipe, unscrew the screw that holds the trap, and remove the trap from the drain extension or drain.
3, according to the need, buy a suitable drain pipe trap, new tail pipe, drainage extension or other accessories. The rotary trap is the easiest to use because you can easily adjust it to change its angle or align it with the drain/component. The drain plug on the trap is also handy. With it, you do not have to remove the trap to clean it.
4. Replace the parts in the correct order and make sure that the sliding nuts, pressure seals, or large washers are installed in the appropriate part of the pipe. Loosely connect the parts together with a sliding nut and make final adjustments so that the pipes are aligned with each other and then tighten the nuts. The tightness can be moderate, not too tight. You don't usually need to use plumber's tape or joint fillers, but you can use it too.
5. Immediately discharge water into the new trap, which can check for leaks and allow these waters to form an important barrier against sewer gas.
Squat toilet trap size
The general size of the squat trap is: length: 585mm* width 470mm* height 296mm.
The relevant information about the trap of the squatting pan was introduced here. I hope this article will be helpful to everyone. If you still have something you don't understand, you can leave a message to Xiaobian at the bottom. We will answer your questions as soon as possible.
Squat toilet squatting toilet how to do the tank squat toilet squat toilet squatting brand what brand is good
1.Quality pass Germany TUV testing. Tuv testing is third safety certificate company,.more authoritative.
2. This system welding machine use Surface Mount System to install electron component and the main PCB board is single .So this system could make the machine`s quality is very stable. Rise the quality consistency.
.
3.The power tube of the switch use germany infineon only.The PCB board thickness size is 2.7mm.
4.The insert component use Taiwan KSS.
5.The aluminum web wing is more bigger and weighter than normal.
6.Passed EMC certificate and get the EMC certificate. According to IEC 60974-1 standard.
7. Our machine`s input voltage is auto change between 85V-240V.So could work under any voltage. Like japan 110V or America 110V AC. Like European 220V-240V AC. Like Brazilian 110V/220V together AC.
8.CEL. Could weld Cellulose electrode easy.
9. Welcome any customer to make your design. We have advanced exploit troop.
10.PFC (Power Factor Correction is more than 98%. So according to energy conversation ,environmental protection and low-carbon.
11. VRD make no-load output voltage under 24±2V, But when arc strike twinkling could rise working output voltage.So this technique could have more physical protection.
industrial Welding Machine,Pigeon Welding Machine,Family Quality Welding Machine
YongKang WALMA Tools CO., LTD. , http://www.walmatools.com