Tiles refer to tiles with porcelain surfaces, while tiles refer to thin-walled patches with porcelain surfaces on the surface of the wall. They are used to decorate the table with several bed cabinets for decorative porcelain products, also known as “inlaid porcelainâ€. More rectangular, or round, elliptical, prismatic, carved or painted on top of flowers and animals, as well as written poetry, Kyrgyzstan. So, do you know the difference between tiles and tiles ? For buyers, it is easy to confuse. The difference between tiles and tiles is mainly the difference in thickness. Tiles are thick and tiles are thin. Find out what is a tile? What is a tile? This is crucial for homeowners who want to make home improvements. In order to help everyone in the purchase of home decoration better, we once again make a simple description of what is the difference between tiles and tiles .
What is the difference between a tile and a tile?
1. The surface requirements are different: There are also differences between tile and tile surface requirements, the smoother the tiles, the better, and the tile requires a rough surface, with a certain degree of slip resistance is good.
2. The use of different: Tile is a kind of ceramic tile (glazed tile) is the best tile on the wall. Tiles refer to tiles that have a porcelain surface, while tiles refer to thin-walled tiles that have a porcelain surface on the surface of the wall.
3. Different classifications and thicknesses: Tiles are thin-walled patches of porcelain on the surface of the wall, while tiles refer to tiles with porcelain surfaces. The most obvious difference between tiles and tiles is that the thickness is not the same, the thickness is obviously different, the tiles are thick, and the tiles are thin.
4. The internal texture is different: Tiles do not require high air bubbles in the interior, and ceramic tiles require that there should be no starburst bubbles inside. Because there are bubbles, the tiles are easily broken by freezing. Tiles should belong to whole-body ceramics, but they do not belong to bricks, but belong to the tiles. Tiles are porcelain and are made of porcelain clay.
5. Different service life: The service life of the tiles is very limited, and the typical service life is about seven years. The water absorption rate of tiles on the market is generally above 10%, and it is easy to crack or even break for a long time. When consumers purchase tiles, they can distinguish whether they are tiles or tiles by weight. In general, tiles are lighter and tiles are much heavier than tiles.
6, the concept is different: tiles refers to the film, generally used to decorate the wall. But the tiles are not in direct contact with the wall, but there is a certain distance from the wall. Although tiles can also be decorated on the wall, but the tile is a block of brick, not a piece, after the paste is completely affixed with the wall, with cement sand fixed in the middle.
Second, on the tiles
(A) Ceramics Buying Tips
There are hopes, smells, questions, and methods of healing in ancient times. In the same way, there are also four-character mouthpieces, such as watch, listen, water and cut. Nowadays when people purchase tiles, people hope to buy good ceramic tile products. How to choose? We can diagnose and test the quality of ceramic tiles by listening, water, cutting, and viewing in different ceramic tile brands.
1. "listen": tap the lower part of the tile, if the voice is clear, sweet for the top grade, such as sound boring, astringent turbidity for the defective.
2. "Water": The water droplets are on the back of the tile. After the water has spread, the tiles that have been soaked slowly have a high density and are regarded as top grade.
3. "Cut": Look at the broken part of the tiles. The fracture is fine, hard and brittle, and the color is consistent with the top grade.
4. "Look": The glaze has no defects, and the pattern is delicate and realistic; the back shading and trademarks are clear and complete.
(b) Porcelain tiles
Choosing a good tile is undoubtedly important, but it is also good value for money and best use. However, how to reflect the value of a good tile? This must pay attention to the details of the operation when making ceramic tiles. The correct tile laying process has a great connection to its life. When paving, pay attention to the tile grades, specifications, color numbers, and the combination of patterns. Except for the special decorative effects that are intentionally pursued, the same room should be tiled with the same grade, size, and color. Tiles are laid out as follows:
1, leveling
Before laying tiles, treat the wall surface of the building to be treated to remove dirt from the surface and moisten the water, then mix and level it with cement mortar and wait until the screed is completely dry and then apply.
2, reserved
When laying tiles according to actual needs, a 2mm-3mm mortar joint should be reserved between tiles to prevent the thermal expansion and contraction coefficient between the wall and tile and the adhesive layer from being inconsistent. Detached tiles, empty drums and other phenomena, resulting in construction quality accidents.
3, line
According to the requirements of the design and layout, determine the row of bricks, and pop up the position of the tiles and the position line of the brick seams on the dry leveling layer.
4, paving
Place the tiles to be laid in clean water for about 1 hour so that they do not bubbling. Then remove and dry the water stains. Spray enough water on the screed and apply evenly about 1:2 cement on the back of the brick. Mortar (concrete qualified ordinary <325# portland cement) after mixing the number below 200# (if the mixed mortar grade is too high, the subsequent stress will cause glazed glazed tiles to produce cracks, easy to cause construction quality Accident): The thickness of the mortar is 5mm-6mm. It should be thickened when paving the large-size tiles, and then affixed with bricks. Use a wooden hammer or a plastic hammer to gently clap, avoid hollowing, and use a ruler or level at any time. Ruler leveling.
5, trimming
After plastering a certain area, grout is filled with cement grout (white cement grout, gypsum grout, etc.) on the brick joints; in the end, dirt on the brick surface shall be removed to strengthen the care.
(3) Precautions for porcelain tiles:
Note 1: The wall to be paved should be soaked (saturated) in the afternoon before the paving.
Note 2: The product must be soaked before it is applied. The bad handling of this move directly affects the shedding of the wall tiles.
Note 3: Paving products should use 325 grade cement, preferably cement + fine sand or cement + gray lamb.
Note 4: The wall should be cut open, and the back of the glazed inner wall tile should not be over 6mm thick when it is coated with cement paste.
Note 5: Glazed interior wall tiles should be avoided from being placed on exterior walls, outside balconies, prefabricated walls, etc.
Note 6: The non-abrasive glazed inner wall tiles should be left in the seams to make the overall paving effect more beautiful.
Three, on the tiles
(a) buy tiles
1, check the label
The product packaging box should have the name, address, product name, after-sales service phone number, specifications, quantity, trademark, production date and the standards implemented. For porcelain tiles, the CCC certification mark must be checked, and the interior design decoration tiles. Should choose radionuclide products that meet Class A requirements.
2, look at the appearance
Good quality ceramic glazed tiles should be smooth, delicate, shiny glaze crystal shiny, soft and comfortable matt glaze. Under full natural light or fluorescent lighting, the bricks should be observed vertically at a distance of 1 meter. No obvious glazed defects should be visible. Patterned brick patterns should be delicate and realistic, with no obvious defects such as lack of color, broken lines, and misalignment. The shading and trademarks on the back of high-quality ceramic products are clear and complete, with few lacquer or defects.
3, stitching effect
Good tile size deviations are small. Place a batch of products vertically on a flat surface to see if there is any unevenness. Looking at the flatness, you can close the edges of two bricks to see if there are any gaps. Good product deformation is small, and the brick surface is flat and beautiful after paving. Look at the color of the product, put together a few bricks, and look closely under sufficient light. Products with different shades of color between the products have poor overall appearance after being laid.
4, percussion listening
Tap the tile gently and listen to the sound. The better quality sounds crisp and sweet. Poor quality products due to improper raw material formulation, firing cycle is short, firing temperature is low, will emit a "empty" sound.
(b) Tile Laying
1. Construction Tools: In addition to the commonly used tools for plastering, the following tools should be prepared: cutting, wood, shovel, hand hammer, alloy steel drill, and cutting machine.
2. Preparation for construction: The base layer shall be treated. The basic surface of the decorative corner shall have sufficient stability and rigidity. The residual mortar, dust and grease on the basic surface shall be cleaned with a wire, and the surface shall be the wall of the paint. The lacquer surface is treated to remove the uneven surface of the substrate surface and should be leveled off or cemented with 1:3 cement mortar.
Water soaking: Clean the glazed bricks before laying them with cement and mortar. Soak them in clean water for at least 2 hours. Soak them until they do not absorb water. Then remove them and use them dry. If you use 903 or 933 glue paste wall tiles, tiles must not be soaked.
Pre-arrangement: pre-paving before paving, pre-arrangement should pay attention to the same wall in the horizontal and vertical arrangements must not have more than one row of non-complete bricks, non-complete bricks should be ranked in the most eye-catching parts or female corner. Method: Use the seam width to adjust the row of bricks. If the design is not specifically determined, the seam width can be adjusted between 1-1.5MM. In the pipeline, lighting fixtures and parts of the sanitary equipment, the application of the entire brick sleeve cut anastomosis, shall not use non-complete brick patchwork to ensure the appearance of the finish.
3, paving: floor tiles in accordance with the indoor standard horizontal line, to find the ground elevation, leveling with a level, the use of cement and fine sand 1:1 mixed slurry for construction; wall tiles need to use level and plumb line paste Measure the horizontal and vertical control lines, and then use cement and fine sand 1:1 mixed slurry for construction or use 903 glue to paste.
4. Closing: After the paving is completed for about 48 hours, use a white cement or a special tile gutter to create a clean and sanitary environment.
Editing Summary: The above is what is the difference between tiles and tiles, experts Weapon: the weight of the contrast to identify the tiles and tiles related to the introduction, the purchaser in the purchase, through the weight of the contrast to identify tiles and tiles. The tiles are generally light, while the tiles are much heavier. For more information, please continue to follow our website. Follow-up will present more exciting content.
What brand of tile is good to stick tiles What glue is used in the bathroom What tiles are good for the kitchen What color tiles are What tiles are good
Soaking Bathtub
Soaking Bathtub
Guangzhou Aijingsi Sanitary Products Co.,Ltd , https://www.comoxvalleyhottubs.com