IP68 High Flashing Reflective LED Aluminium Wire Road Studs for Tunnel 100 * 105 * 19 mm

IP68 High Flashing Reflective LED Aluminium Wire Road Studs for Tunnel 100 * 105 * 19 mm

Specification:
 
Description:
Tunnel wired road studs is also called photoelectric pavement marker,LED road stud and road pavement marker.The mainly function is Pavement sight induced warning.It Is a clear, eye-catching adjustable active flashing light led road signs,Continuously laying a light-emitting lane contour line.
It is not only play excellent guide obvious warning but also add beautiful landscape.It is mainly install in the main highways, tunnels, approaches shoulder, around the island, traffic islands, underground parking entrance of the tunnel wall and the curb or on the road along the side walls.
     
Applications:
1. Highway.
2. Bridge.
3. Construction Site.
4. Tunnels.
5. Approaches shoulder.
6. Island.
7. Traffic islands
8. underground parking entrance of the tunnel wall.
9. Curb or on the road along the side walls.
10. Freeway (ramp), turn the larger road toll station entrances.
11. The school gate, cell junctions, intersections, traffic lights, hotels, parks, tunnels, curbs, underground garage entrance (exit).
 
Installation Details:
1. When install the road studs,it need Set security facilities and configuring security personnel to ensure the safety of the installation work carried out.
2. Need check the location of the installation required a flat, specifications.
3. Try to choose sunny weather construction to make sure the floor is clean, dry (with fixed spike glue must be clean, dry ground).
4. When the glue is installed: appropriate amount of glue needed to ensure that the bottom was saturated sticky glue, such as glue, there is the need to clean up the spill,
Press the spike at the installation location, ensure correct orientation.
5. Cast aluminum with foot installation: holes deeper than "nail pin" depth 1cm, hole diameter is larger than the "nail pin" diameter 2mm (control between 2-5mm).
6. After installation is complete, once inspections to ensure proper installation position of the spike, there is no anti-loaded, installed crooked.
7. After curing spike more than 4 hours, evacuate install security isolation facilities.
 
Features:
1. Working voltage: 24VDC or 220VAC

2. Using high brightness LED light source, double-sided light, luminous uniform, soft light, no glare, good stability. Our new plate imported from Taiwan LED chip, more than ten years has been very focused traffic stable.

3. Constant product installation, interference chips, LED use of more stable and longer life, the light fades smaller life> 3 years.

4. Equipped with spike protection circuit can be the product of effective protection, improve product performance, to avoid a single internal fault protruding signs induced impact on the entire system.

5. Warning strong, visible from up to 500 meters


Company Profile:

JACKWIN is a professional supplier, specialized in developing, designing, manufacturing and exporting a wide range of roadway safety,parking,site and construction facilities.We have a broad range of products that we self-designed with excellent quality for clients' choice and the strong ability for injection and blowing moulding process in our R&D department makes plastic products in various sizes, shapes and colors with superior strength in short lead-time with lower developing and manufacturing cost to satisfy customers from allover the world.
Our products cover the markets in North and South America, Europe,East Asia, the Middle East and Africa and we emphasize on goods quality to meet clients' requirements and win markets in their areas. We have a strict and perfect Quality Control System that makes each process have high quality standard not only in material and half-products but in final products.
 
"High Quality, Reasonable Price, Best Service, Right & Prompt Delivery"  is our company's philosophy, we commit ourselves to innovate products to meet various needs of our clients and promote equal and mutual-benefits business relationships.
Our company can supply OEM and ODM services for customers all over the world, welcome to visit our website and inquire for catalogue and price at any time.
Aftersale Service:
1.Two year warranty policy.
2.We test all the products 3 times before delivery.
3.Good delivery time.
 
Payment:
Payment: L/C,  T/T  Western Union,  Trade Assuarance,  Paypal

Product Packaging:Cartons

 
FAQ:
Q: Can your produce customized goods ?     
 
A: Yes, the size, the height and the weight can be produced as per client's requirements.  
 
Q: Can you print words on products as per client's requirement?   
 
A: Yes, make label according to your exact requirement.    
 
Q: Can you do business via Ali Online Transaction?      
 
A: Yes, we can make the deal through AOT.     
 
Q: What is your payment terms?   
 
A: T/T, L/C at sight or Paypal.   
 
Q: Do you accept OEM?    
 
A: Yes, OEM or ODM are both OK.  
 
Q: Where is your nearest loading port ?   
 
A: Ningbo, China.   
 
Q: How can you guarantee the quality or any warranty?  
 
A: If have any quality problems during use, all the products can be returned or according to consumer's requests.

 
IP68 High Flashing Reflective LED Aluminium Wire Road Studs for Tunnel 100 * 105 * 19 mm

Specification:
 
Description:
Tunnel wired road studs is also called photoelectric pavement marker,LED road stud and road pavement marker.The mainly function is Pavement sight induced warning.It Is a clear, eye-catching adjustable active flashing light led road signs,Continuously laying a light-emitting lane contour line.
It is not only play excellent guide obvious warning but also add beautiful landscape.It is mainly install in the main highways, tunnels, approaches shoulder, around the island, traffic islands, underground parking entrance of the tunnel wall and the curb or on the road along the side walls.
     
Applications:
1. Highway.
2. Bridge.
3. Construction Site.
4. Tunnels.
5. Approaches shoulder.
6. Island.
7. Traffic islands
8. underground parking entrance of the tunnel wall.
9. Curb or on the road along the side walls.
10. Freeway (ramp), turn the larger road toll station entrances.
11. The school gate, cell junctions, intersections, traffic lights, hotels, parks, tunnels, curbs, underground garage entrance (exit).
 
Installation Details:
1. When install the road studs,it need Set security facilities and configuring security personnel to ensure the safety of the installation work carried out.
2. Need check the location of the installation required a flat, specifications.
3. Try to choose sunny weather construction to make sure the floor is clean, dry (with fixed spike glue must be clean, dry ground).
4. When the glue is installed: appropriate amount of glue needed to ensure that the bottom was saturated sticky glue, such as glue, there is the need to clean up the spill,
Press the spike at the installation location, ensure correct orientation.
5. Cast aluminum with foot installation: holes deeper than "nail pin" depth 1cm, hole diameter is larger than the "nail pin" diameter 2mm (control between 2-5mm).
6. After installation is complete, once inspections to ensure proper installation position of the spike, there is no anti-loaded, installed crooked.
7. After curing spike more than 4 hours, evacuate install security isolation facilities.
 
Features:
1. Working voltage: 24VDC or 220VAC

2. Using high brightness LED light source, double-sided light, luminous uniform, soft light, no glare, good stability. Our new plate imported from Taiwan LED chip, more than ten years has been very focused traffic stable.

3. Constant product installation, interference chips, LED use of more stable and longer life, the light fades smaller life> 3 years.

4. Equipped with spike protection circuit can be the product of effective protection, improve product performance, to avoid a single internal fault protruding signs induced impact on the entire system.

5. Warning strong, visible from up to 500 meters


Company Profile:

JACKWIN is a professional supplier, specialized in developing, designing, manufacturing and exporting a wide range of roadway safety,parking,site and construction facilities.We have a broad range of products that we self-designed with excellent quality for clients' choice and the strong ability for injection and blowing moulding process in our R&D department makes plastic products in various sizes, shapes and colors with superior strength in short lead-time with lower developing and manufacturing cost to satisfy customers from allover the world.
Our products cover the markets in North and South America, Europe,East Asia, the Middle East and Africa and we emphasize on goods quality to meet clients' requirements and win markets in their areas. We have a strict and perfect Quality Control System that makes each process have high quality standard not only in material and half-products but in final products.
 
"High Quality, Reasonable Price, Best Service, Right & Prompt Delivery"  is our company's philosophy, we commit ourselves to innovate products to meet various needs of our clients and promote equal and mutual-benefits business relationships.
Our company can supply OEM and ODM services for customers all over the world, welcome to visit our website and inquire for catalogue and price at any time.
Aftersale Service:
1.Two year warranty policy.
2.We test all the products 3 times before delivery.
3.Good delivery time.
 
Payment:
Payment: L/C,  T/T  Western Union,  Trade Assuarance,  Paypal

Product Packaging:Cartons

 
FAQ:
Q: Can your produce customized goods ?     
 
A: Yes, the size, the height and the weight can be produced as per client's requirements.  
 
Q: Can you print words on products as per client's requirement?   
 
A: Yes, make label according to your exact requirement.    
 
Q: Can you do business via Ali Online Transaction?      
 
A: Yes, we can make the deal through AOT.     
 
Q: What is your payment terms?   
 
A: T/T, L/C at sight or Paypal.   
 
Q: Do you accept OEM?    
 
A: Yes, OEM or ODM are both OK.  
 
Q: Where is your nearest loading port ?   
 
A: Ningbo, China.   
 
Q: How can you guarantee the quality or any warranty?  
 
A: If have any quality problems during use, all the products can be returned or according to consumer's requests.

 

Scaffolding Tube And Coupler

Scaffolding Tube And Coupler, Scaffolding,Iron Pipe & Tube,Construction Accessories

Ringlock Scaffolding System,Kwikstage Scaffolding Co., Ltd. , http://www.nbscaffolding.com