How to install solid wood wallboard solid wood wallboard installation precautions

Solid wood wallboard is one of the common decorations in home decoration. Solid wood wallboard can make our interior highlight style, so it will be liked by many consumers. But everyone knows about the installation of solid wood panels? Today Xiao Bian will take a look at how to install solid wood panels and want to change knowledge. Friends in need can look!

How to install solid wood wallboard

1, keep the wall clean

Before preparing to install solid wood wall panels, it is necessary to thoroughly clean the walls and keep the walls clean and dry and flat. In order to adapt the wood panel to the local climate temperature and reach the moisture content of the air, the purchased wall panels should be unpacked and stored in place for at least 48 hours before installation.

2, the size of the design in advance

It is also very important to design the partition size of solid wood wall panels. Each wall surface should be straightened and tested and installed once. After being adjusted and repaired, it will be installed afterwards. This will prevent the pattern of the surface layer from being disordered and the color from being uneven. The edges and corners are not straight, the surface is uneven, there are black lines at the joints and the joints are not strict.

3, pull the line to check the roof

Before the construction, it is necessary to pull the wire to inspect the solid wood wallboard to see if the top of the solid wood wallboard is straight and correct any problems in time. Avoid the thickness of the top panel of solid wood panels, unevenness, chapped, etc.

4, the wall needs to do moisture treatment

Due to the large moisture content of the wood, it tends to shrink after drying, resulting in loose joints or cracks. Therefore, if the wall is wet, it should be dry after construction or moisture treatment.

5, the panel surface to leave a gap

The height difference of the surface of the solid wood panel panel should be less than 0.5mm; the width of the left seam between the panel surface should be uniform, the size deviation should not exceed 2mm; the deviation of the diagonal length of the single panel should not exceed 2mm; the panel vertical deviation should not exceed 2mm .

6, yin and yang angle should be horizontal and vertical

The yin and yang corners of solid wood wall panels are the focus and difficulty of construction, and special attention should be paid. Must be vertical and horizontal yin and yang, seam stitching 45 °.

7, baseboard and layering should be close to the panel

Skirting boards and beadings should be close to the panel, leaving no large gaps. The distance between the nails of the fixed skirting board or bead shall not be greater than 300mm; the nail cap shall be flattened and the depth of the nail into the slats shall be 0.5-1.0mm. The nail must be smoothed with the same color oily putty.

The above is how to install and install the solid wood wallboard for everyone. After reading, it is not more understanding of solid wood wallboard installation. I hope the above can help you. If you want to know other related information, please Continue to pay attention to this site, more exciting so stay tuned!

Solid wood panel



Pyrite as Fillers Used in Steelmaking and Core-Spun Yarn

Steel-making/casting core-clad wire (filling material)

Place of Origin: Henan Luoyang, China

Pyrite, Iron pyrites , pyrites lump, Ferro sulphur, Pyrites powder.

Product Description:

Detailed introduction: Is used as the filling material of cored wires and resulfurization additive agent for steel-making and casting.  It is used for adding sulfur element in steel smelting to improve the cutting performance, inoculation effect, graphite shape and mechanical properties of gray pig iron.

Quality:

S: 48%min, FE: 42%min, SIO2: 3.0%max, PB: 0.1%max,

ZN: 0.1%max, AS: 0.1%max, . C: 0.3%max, CU: 0.2%max,

H20: 1.0%max, SIZE: 95%min

Granularity: (0-3)mm/(3-8)mm/(3-15)mm/(15-50)mm or other particle size.

Packing: 25KG/500KG/1000KG/BAG or 1000KG/BAG or other packaging.

Note: if there are special requirements, the product can be customized according to clients` requirements.


Steel-making/casting Core-clad Wire --BXX

Pyrite, Iron pyrites, pyrites lump, Ferro sulphur, Pyrites powder.

LUANCHUAN COUNTY HENGKAI METALLURGICAL MATERIALS SALES CO.,LTD , https://www.pyritechina.com

Posted on