| Home>Bearing knowledge> FAG imported bearing device and application method |
FAG imported bearing device and application method
| /*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089'; |
1; adhere to FAG imported bearings and its surrounding health.
Even small dust that cannot be seen by the eyes will have a bad influence on FAG bearings. Therefore, it is necessary to adhere to the surrounding sanitation; so that the dust does not invade the bearings.
2; Carefully use the FAG imported bearings to give the bearing a strong impact in the application; there will be scars and indentations; the cause of the incident. In severe cases; cracks, cracks; so it is necessary to pay attention.
3; Use appropriate operational things to prevent substitution with existing things; it is necessary to use the right things.
4; Pay attention to the rust-operated bearing of FAG imported bearings; the sweat on the hand will become the cause of rust. Pay attention to the use of clean hands; the best possible to bring gloves.
FAG bearing device method Many users know the FAG bearing; but the FAG bearing device method is not very well known; the device is good or bad; it will affect the bearing accuracy, life and function. Therefore, it is necessary to fully study the FAG bearing device. Ways; advocate the user to carry out the device according to the following operating rules; specific methods:
a. Pressing into the cooperation FAG bearing inner ring and the shaft to make tight cooperation; when the outer ring and the bearing housing hole are loosely cooperative; the bearing can be pressed on the shaft by the press; then the shaft is loaded into the bearing housing hole together with the bearing; Pressing on the end face of the inner ring of the bearing; padding a device casing made of soft metal material (copper or mild steel); the inner diameter of the casing of the device should be slightly larger than the diameter of the journal; the diameter of the outer diameter should be smaller than the inner ring of the bearing Slightly. Banyan 3 is intended. The outer ring of the bearing is tightly cooperating with the bearing housing hole; when the inner ring and the shaft are loosely engaged; the bearing can be pressed into the bearing housing hole first; Slightly smaller than the diameter of the seat hole. If the bearing ring and the shaft and the seat hole are tightly cooperated; the inner ring and the outer ring of the device should be pressed together into the shaft and the seat hole; the layout of the device bushing should be able to tighten the inner ring of the bearing together And the end face of the outer ring.
Usually the new bearing is the best to open the cover and refueling; it can be used without oiling. However, the FAG bearing is the best addition of molybdenum disulfide lithium base grease; due to its high temperature and wear resistance, the calcium base grease is not Gradually screen with high temperature resistance; the best time to remove the oil of the original bearing. The best bearing of the motor does not exceed 70 degrees; especially the high speed bearing; high speed loss; should be refueling; the best for the gearbox should not exceed 60 degrees Because the organic oil inside the gearbox is smooth; the summer temperature is 60 degrees. The best bearing on the pump should not exceed 65 degrees.
Recommend to friends comments close window
| Bearing related knowledge |
| The reason why the bearing is formed by the grinding spiral is the basic concept of the one-way bearing. The appearance of the NSK bearing temperature rise analysis and detection methods rolling bearings from production to the device to the use; its play has a change? |
This article links to http://
Please indicate the bearing network http://
Previous:The principle and application of self-smooth bearing analysis:The use and protection of bearings
Hot-Melt Bookbinding Adhesives
The term [perfect binding" was created in 1911 to describe the hot-melt adhesive application in the bookbinding process.
At that time, hot melts attempted to overcome the disadvantages of emulsion adhesives while retaining the desirable characteristics of pull strength and flexibility. The driving force toward hot-melt adhesives was their high speed, minimal waste, and relatively low cost.
Our company chaobang adhesive co., Ltd. set up in 1999, we are professional Hot Melt Glue manufacture. Our company has been committed to the Bookbinding Glue for nearly 20 years. In the company's development process, we meet with many different questions and we solved those questions. our company has been developing steadily. We are trying to get better and better. We must do our best to make the good quality product, we must produce the suitable product for the market. Believe us, chose us is right.
Bookbinding Glue
Book Binding Glue,Book Binding Adhesive,Paper Binding Glue,Book Binding Tape
Taixing Chaobang Adhesive Co., Ltd. , http://www.cb-adhesive.com